VELLUM THERMAL TRANSFER LABEL 25mm x 25mm

Freeze Adhesive Specification

25.09.2009 ENG 540

ADHESIVE

RP 48

Deep Freeze

RP48 (sales code)

Type

Deep-freeze permanent adhesive.

Composition

Acrylic, water borne.

Use

Should be used when very good adhesion at low temperatures is required. Adhesion to non-polar surfaces is very good. Remains adherent at low temperatures.

Typical technical values

Tack min

5

N

FTM 9

Shear min

0.5

h

FTM 8

PE-looptack min

5

N

modified FTM 9

Labelling temperature min

-20

°C

Service temperature min

-40

°C

Service temperature max

60

°C

Limitations

Limited heat resistance. Should not be used in places where temperature is significantly above room temperature. Convertibility not as good as with other permanents. Edge-bleeding may occur. Not suitable for labelling curved surfaces. Limited adhesion to moist surfaces.

Approvals

The research centre ISEGA has given the adhesive approval for direct contact with dry and moist and such kind of fatty foods which have a reduction factor of at least 3 according to the EC directive 85/572/EEC.

Shelf life

From the date of manufacture 1 year in +20°C and RH 50% .

Warranty
Our recommendations are based on our most current knowledge and experience. As our products are used in conditions beyond our control, we cannot assume any liability for damage caused through their use. This publication replaces all previous versions. All information is subject to change without notice.

Vellum Thermal Transfer Labels Face Specification

16.06.2010 ENG 302

SELF-ADHESIVE

ROLLS

FACE

VELLUM TTR

Uncoated

02 (sales code)

Product

Surface sized woodfree supercalandered paper.

Use

Universal label paper for commercial and general labelling.

Typical technical values

Substance

70

g/m²

ISO 536

Caliper

70

µm

ISO 534

Tensile strength MD

6.0

kN/m

ISO 1924/1

Tensile strength CD

2.3

kN/m

ISO 1924/1

Brightness

95

%

ISO 2470/1

Roughness

2.7

microns

ISO 8791

PPS 10

Opacity

90

%

ISO 2471

Stiffness MD

0.18

mNm

ISO/DP 2493

Stiffness CD

0.10

mNm

ISO/DP 2493

Printability

Flexography, offset, letterpress, thermal transfer, dot-matrix.

Warranty
Our recommendations are based on our most current knowledge and experience. As our products are used in conditions beyond our control, we cannot assume any liability for damage caused through their use. This publication replaces all previous versions. All information is subject to change without notice.

Permanent Adhesive Specification

07.10.2009 ENG 186

ADHESIVE

RP 51

Permanent

RP5X (sales code)

Type

General purpose strong permanent.

Composition

Acrylic, water borne.

Use

Good adhesion to all normal substrates, including non-polar surfaces, films, and corrugated board. Good low temperature performance.

Typical technical values

Tack min

15

N

FTM 9

Shear min

1.0

h

FTM 8

PE-looptack min

10

N

modified FTM 9

Labelling temperature min

0

°C

Service temperature min

-20

°C

Service temperature max

80

°C

Limitations

Not recommended for labelling highly curved surfaces.

Approvals

The research centre ISEGA has given the adhesive approval for direct contact with dry and moist non-fatty foods.

Shelf life

From the date of manufacture 4 years in +20°C and RH 50%.

Warranty
Our recommendations are based on our most current knowledge and experience. As our products are used in conditions beyond our control, we cannot assume any liability for damage caused through their use. This publication replaces all previous versions. All information is subject to change without notice.

Removable Adhesive Specification

21.02.2011 ENG 470

SELF-ADHESIVE

ROLLS

FACE

THERMAL TOP P 200

Thermal Top

HN (sales code)

Product

Top and reverse side barrier coated, chemi-thermal paper with standard sensitivity.

Use

Wide range of information and product labelling requiring good environmental resistance of the printed image and standard sensitivity performance.

Typical technical values

Substance

73

g/m²

ISO 536

Caliper

76

µm

ISO 534

Tensile strength MD

4.1

kN/m

ISO 1924/1

Tensile strength CD

2.3

kN/m

ISO 1924/1

Brightness

91

%

ISO 2470/2

min

Smoothness

200

Bekk sec

ISO 5627

min

Density

1.20

min

Imaging colour

Black

Scanning

Visible red light.

Printability

Flexography solvent based, water based needs to be checked (humidity and water resistance of the ink), letterpress, offset, screen, UV varnishing. Thermal direct.

Additional info

For standard printers up to 200 mm/s.

Storage recommendations

Store at a constant temperature (20°C, RH 50%) in the dark. Damp or hot conditions should be avoided.

Shelf life

A) Dispersion adhesives (except RP45, RP48, RR21, RR22). The laminate is guaranteed for two years if stored in the above conditions. B) RP45, RP48, RR21, RR22 and hot melt adhesives. The laminate is guaranteed for one year if stored in the above conditions.
C) Printed labels are guaranteed for one year if stored in the above conditions. Face paper has a slight tendency to discolour, but this does not affect the scannability of the barcodes.

Warranty
Our recommendations are based on our most current knowledge and experience. As our products are used in conditions beyond our control, we cannot assume any liability for damage caused through their use. This publication replaces all previous versions. All information is subject to change without notice.